Retail banks wake up to digital lending this year

Companies seem to dislike the term ‘turnaround consulting’ because it represents failure. The truth is that turnaround consulting represents success at realizing the company is going in the wrong direction. The only time the company fails is when it is not possible to do a turnaround anymore. We help companies pivot into more profitable directions where they can expand and grow. It is inevitable that companies will end up making a few mistakes; we help them correct these mistakes. We help companies turnaround their non-profitable ventures into something that benefits them. Our specialty lies in understanding what makes a company special [...]

Retail banks wake up to digital lending this year2019-09-27T04:18:23+05:30

Seven weeks working ‘pro bono’ with a charity

Companies seem to dislike the term ‘turnaround consulting’ because it represents failure. The truth is that turnaround consulting represents success at realizing the company is going in the wrong direction. The only time the company fails is when it is not possible to do a turnaround anymore. We help companies pivot into more profitable directions where they can expand and grow. It is inevitable that companies will end up making a few mistakes; we help them correct these mistakes. We help companies turnaround their non-profitable ventures into something that benefits them. Our specialty lies in understanding what makes a company special [...]

Seven weeks working ‘pro bono’ with a charity2019-09-27T04:17:28+05:30

Modeling of pulse position

In pulse location modification, the position of the pulse changes as a modified signal function, and the pulse width and width is always maintained. The position of each pulse varies according to the instantaneous sampling of the modified signal. To implement the pulse site modification, two integrated 555 timer circuits, one in stable mode and one in isolation mode are used. The signal modification is applied to the first 5 pin of 555 IC, which operates in a stable mode. The output of IC 555 is a modified wave of pulse width. This PWM signal is applied as a stimulus input [...]

Modeling of pulse position2019-04-26T17:42:44+05:30

Square wave Generation using 555 Timer

Square wave generation using 555 timer IC need extra circuit arrangement in astable multivibrator. For Square wave generation duty cycle should be 50% and with the help of 555 timer IC. So a diode connected parallel with the R2 resistor. At charging time resistance R1, diode and capacitor come in the picture and discharge through diode D2, resistance R2 via discharging pin number 7 of 555 timer IC. By adjusting the values ​​of resistors R1 and R2, a working cycle can be found between 5% and 95%, plus the square wave output. The square wave generation circuit is shown below. To [...]

Square wave Generation using 555 Timer2019-04-25T14:25:36+05:30

Astable Multivibrator using 555 Timer

Astable Multivibrator using 555 Timer Circuit and operation Astable Multivibrator using 555 Timer has no state stable. It generated free running frequency without any output source. The IC 555 can be used as an independent multivibrator with three external components: two resistors (R1 and R2) and capacitor (C). The diagram for IC 555 timer is shown below in the figure with external components. Pins 2 and 6 are connected with each other and no external stroke is required. Activate automatically and act as a free multi-generator. The other connections are as follows: pin 8 is connected to the supply voltage (VCC). [...]

Astable Multivibrator using 555 Timer2019-04-24T17:33:17+05:30

The Monostable 555 Timer

555 hours per hour The operation and output of the mono-stabilizer 555 is exactly the same as the transistor described in the Multi-Traceability Uniform tutorial. The difference is that the 555 timer is replaced. Consider 555 hours of circuits below. 555 tangible time When a negative pulse (0 V) is applied to the mandatory input (pin 2) of the configured oscillator 555, this input is detected in the internal comparator (comparator # 1) and "sets" the state of the chipboard through switching the output off from "LOW" to "HIGH" mode, this process removes the connection transformer connected to pin 7, removing [...]

The Monostable 555 Timer2019-04-18T17:43:20+05:30
Go to Top